Where to Install ONTs in Hotels and Hospitals

Nov 09, 2026

Leave a message

Glory Optical Engineering Team
Glory Optical Engineering Team
The Glory Optical Engineering Team​ is an elite group of senior telecommunications experts, structural engineers, and network architects. Serving as the core technical engine behind Glory Optical Communication.

A case-based comparison of ceiling, cabinet and wall locations, with a passive fiber selection table and an RFQ field list.

At Hospital São José, clinical devices and workstations plug into wall-mounted RJ45 outlets. The optical network terminals (ONTs) that serve those outlets sit above a suspended ceiling or inside an optical termination box, according to the supplier's case study. Where people plug in, where fiber ends, and where technicians replace the ONT are three decisions on the floor plan.

This guide compares three locations (above a suspended ceiling, inside a cabinet or furniture, and in or on a wall), shows how to check service access, heat and power before the layout is frozen, and finishes with a passive fiber selection table and an RFQ field list to send with your drawings.

Case marks what the supplier reports about the project. Criterion marks an engineering trade-off or a check to apply to your own drawings.

How Hospital São José Separated the ONT From the Room Outlet

Hospital São José added a new building and needed a network that could support both clinical and administrative areas. Lightera lists electronic health records, connected medical devices, IP telephony, security, staff and patient Wi-Fi, and building automation among the services. The project used Lightera's Laserway passive optical LAN with Nokia networking technology. The installer had to bring Ethernet to the places where staff needed it while finding practical locations for the powered equipment. Lightera's Hospital São José case study

Why the Administrative ONTs Stayed Near the Workstations

Case In offices, the team placed ONTs under workstations, inside cabinets and office furniture, or near users. Lightera says this kept workspaces tidy, reduced the need for additional infrastructure, and eased maintenance.

Criterion A desk or cabinet position can give technicians direct access and keep the Ethernet run to nearby devices short. A shared telecom room may be easier to secure and power, but every workstation it serves needs an Ethernet route back to that room. Use the local position where the cabinet can open with the furniture in place, the ONT can come out without moving the desk, and the closed cabinet meets the model's temperature and clearance requirements.

Why the Clinical Outlets Stayed on the Wall

Case In care areas, the team put ONTs above suspended ceilings or inside optical termination boxes. Ethernet ran from those ONTs to the RJ45 outlets used by clinical equipment and workstations. Lightera reports that the arrangement kept powered hardware outside patient-contact areas and reduced the amount of visible equipment.

Criterion A visible wall-mounted ONT can be quick to reach, but it brings the powered device, its cables, and the space needed to replace it into the care area. An above-ceiling position frees that wall space when a usable hatch, mounting point, and power feed are available. A box with a reachable cover can make a better service point where ducts block the hatch or where opening the ceiling would disrupt care. The box still needs room for the connector bends, equipment removal, and heat under load. Confirm patient-area surface materials and cleaning requirements with the hospital.

Two path diagrams. Administrative areas: floor fiber to an ONT under a desk or in a cabinet, then network cable to an office device. Clinical areas: floor fiber to an ONT above the ceiling or in an optical termination box on the service side, then network cable to a wall RJ45 outlet and a clinical device or workstation on the use side.

Figure 1. Hospital São José ONT paths, redrawn as a schematic from the published text. It illustrates the principle and is not a project drawing.

How to Lay Out a Similar Care Area

  1. Place the RJ45 outlets around the care workflow. Give each outlet an ID and map it to the serving ONT and Ethernet port so staff can trace a fault from the room.
  2. On the ceiling or wall drawing, mark the ONT, the fiber and copper routes, the power feed, and the side from which a technician can work. Review the access route with clinical and facilities staff to see whether a repair would require entering an occupied room.
  3. Build one representative location with the intended ONT, cables, and box or bracket. Run it with the cover closed at the expected load, then have a technician trace a labeled outlet and replace its ONT through the planned opening. Record which outlets lose service during the swap.

The published hospital layout establishes the two installation patterns. Confirm the equipment model, box construction, hatch dimensions, power and backup design, and temperature results from project records before using it as an installation specification.

Choosing Between Ceiling, Cabinet, and Wall Locations

Choose by what a technician must do on replacement day. Installation is the easy visit; the swap years later is the test. The three common positions differ in access, heat and where power comes from.

Above a suspended ceiling

Above-ceiling ONT installation suits care areas where only the outlet should be visible. Pick a unit approved for the space. Tellabs lists its FlexSym ONT202 as plenum rated for above-ceiling mounting (UL 2043 plenum fire test), with bracket and DIN-rail options and an industrial −40 to 60 °C range. Other models carry different ratings, so read each datasheet. Then check the bracket or tile support, the position and size of the access opening, slack for fiber and copper, and the power route. A hatch that opens beneath a fixed pipe or duct still blocks the swap.

Inside a cabinet or furniture

Hospital São José used office furniture and cabinets for administrative ONTs, and Tellabs describes its ONT140W as suitable for integration inside office furniture. In a closed cabinet, check the temperature with the door shut and the ONT loaded, the nearest power source, and the removal path with cables connected. A television cabinet with a rear inspection panel works only if the panel can be reached with the furniture in place. Furniture also moves during refits, so record the ONT's position on the as-built drawing.

In or on a wall

A wall-mounted ONT takes two forms, and drawings should name which. An embedded unit sits in a back box. The Tellabs ONT140W uses a modular single- or dual-gang back box that holds fiber slack and DC power termination, with electronics and faceplate added later. A Lightera datasheet lists its LW110-20BP as mounting in a standard 4 × 2 in box or on a wall surface (137.5 × 96.5 × 28 mm, two PoE ports); confirm current availability with the supplier. A wall-mounted enclosure is a separate box fixed to the surface. For either form, check device orientation, the depth the connector and bend consume once plugged in, and room to open the cover. A shallow box can fit the ONT yet leave no space for the fiber to bend.

Above a suspended ceiling

Side view of an ONT on a hanging bracket in a ceiling void. Fiber enters from the left, power from the right, and the unit is removed downward through a ceiling hatch.

Inside a cabinet or furniture

Side view of an ONT on a shelf inside a cabinet. Fiber enters from below, power from an outlet inside the cabinet, and the unit is removed through an access panel on the right.

In or on a wall

Side view of an ONT in a recessed wall back box. Fiber enters from above inside the wall, power from below, and the unit is removed through the faceplate opening into the room.

Figure 2. One ONT body in three positions. Blue arrows show fiber entry, dark arrows show power and orange arrows show the direction of removal. Schematic only; dimensions depend on the selected model.

How Wellington Airport Hotel Grouped Its ONTs

Case The 134-room hotel had been designed for structured cabling before the optical LAN was introduced. According to Nokia, the existing design constraints prevented the team from placing an ONT in every room, and higher-density ONTs were unavailable to the project at the time. The integrator, Lexel Systems, grouped four-port ONTs at central locations and used longer Ethernet runs from the switch cupboards toward the hallways outside the rooms. Lexel staged and tested much of the equipment before installation. Nokia's Wellington Airport Hotel case study, pages 2 and 4–5

Case The hotel also put guest-room service hubs behind artwork along the corridors, allowing staff to service those points without entering guest rooms. The network went live in January 2019. The exact relationship between the ONT clusters and the hallway hubs is a detail to confirm on the project drawings.

Criterion One ONT per room can shorten the in-room copper runs and limit the impact of an individual ONT failure to that room. It also requires a fiber route, power, and a reachable mounting position in each room. Grouping ONTs gives technicians a common location to work from, but increases the copper distance to some outlets and concentrates the demand for power and cooling. When one ONT serves several rooms, a swap can interrupt each room attached to it.

How to plan a similar floor

  1. Mark the guest-room outlet, the ONT cluster, and the hallway service point as separate items. Trace the copper path and check the longest complete channel, including patch cords, against the applicable Ethernet and PoE requirements.
  2. Make a room-to-port schedule. For each ONT and shared power feed, list the rooms and devices that would lose service during a fault or replacement. Check whether that outage scope fits the hotel's service requirements.
  3. Stage one group before installation. Label both ends and verify the required room services on a representative channel. Measure the temperature with the cabinet closed under the expected load, then rehearse a replacement from the planned service position.

Check Service Access, Heat, and Power Before Freezing the Layout

Three questions decide whether a location works in service. Answer each with the chosen ONT model and a physical sample before the plan is frozen.

Can a technician replace the ONT?

Rehearse the swap on a real unit or mock-up. Open the access point from the planned service position, find the label, remove the cover, isolate power, unplug fiber and copper, take out the unit, fit the new one, inspect and clean the connector, restore power and confirm the port returns. Time the sequence. Note every step that needs a second person, a ladder, a special tool or the removal of neighbouring equipment. If the swap cannot be finished through the planned opening, move the opening or the unit.

What happens when the cover is closed?

Datasheet temperatures describe the ambient air around the device, and they differ by model. The examples in this article range from 0–40 °C for Lightera's indoor LW110-20BP and 0–46 °C for the Tellabs ONT140W to −40 to 60 °C for the industrial-rated ONT202. A closed box or cabinet also holds the heat of the power adapter, any PoE load and neighbouring equipment. Lightera's remote-power distribution unit, for instance, lists two fans and a 0–40 °C range. Test the chosen model with the cover closed, the expected PoE load connected and every other device in that space running, then record the temperature.

What stays online during an outage?

Keep three numbers apart. The first is the ONT's own input power. The ONT202 datasheet lists 52–57 Vdc and 6.8 W consumption; the ONT140W lists 8 W without PoE. The second is the PoE passed to downstream devices: up to 60 W across four ports on the ONT140W, and up to 120 W on the ONT202 with the proper supply, which Tellabs lists as a 54 V, 2.8 A adapter. The third is what the backup source covers: the OLT, the ONT and every dependent device such as access points, cameras and IP phones.

Then compare feeds. A local adapter needs an outlet beside each ONT and stays online only if that outlet is on backed-up supply. Remote DC powering moves conversion to a central plant with batteries. Tellabs describes DC delivered over CATx or hybrid fiber/copper cable from a bulk plant with emergency power and battery backup. Lightera's Laserway PDU feeds eight ONTs over hybrid cable at up to 62 W per port, leaving 52 W after a 10 W LW110-20BP. Use only the method the ONT model supports.

Specify the Right Fiber Outlet or ONT Enclosure

Passive Fiber Hardware by Installation Point

Select passive fiber hardware for the point where the fiber terminates. A compact wall outlet can serve a single room or workstation, a splice box can organize several fibers in a service cabinet, and a rack-mounted panel can handle fiber patching in a telecom room.

First decide from the drawings whether a box terminates fiber or houses an active ONT. A fiber outlet or termination box holds adapters, splices and slack. An ONT enclosure holds powered equipment and needs room for heat, power and service. Glory's guide to termination boxes versus distribution boxes covers the splitter question, and the FTTH last-meter adapter guide covers adapter and polish choices.

The three Glory items below are general selection examples for a fiber termination point. The bills of materials for the Hospital São José and Wellington projects are not public, so none of these parts is claimed for either project.

Product recommendations by installation point

Installation point Glory option Listed specifications Confirm before ordering
Single room or workstation fiber point GL-2-B Wall Fiber Rosette Box 86 × 86 × 27 mm indoor faceplate; ABS; up to 2 fibers; SC or FC simplex adapters; IP45 dust protection; internal bend radius ≥ 40 mm. Fiber count, adapter type and end face, wall entry, patch cord length.
Corridor cabinet or service area, several fibers GL-B25-8A Optical Fiber Termination Box 235 × 126 × 52 mm; up to 8 fibers; splice and slack storage; SC or LC by project; PC+ABS, IP54; for indoor or sheltered locations. Loaded adapters, splice configuration, clearance to open the cover and flip-up panel; splitter size if the topology splits here.
Floor telecom room with a rack GL-ODF-24 Optical Fiber Patch Panel 2U; 482 × 260 mm footprint; listed capacity 24 fibers; 1.2 mm cold-rolled steel; 19-inch rack. Rack depth, free U space, fiber count, adapter loading (confirm whether the listed capacity counts terminations or adapter positions), port numbering.

Enclosures That House an ONT

When the ONT goes inside a box, size the box from the ONT outward. Add the device body and its bracket, the connector with its plug and bend, the power connector and the copper cable exits, then add room for a technician's hands. Check airflow, the power supply position and the opening used for removal. Whether an enclosure suits an ONT depends on the ONT model and the installation conditions, so confirm it from both datasheets and a sample fit. Treat the Glory items above as passive fiber hardware.

Use a Mock-Up Before Ordering the Full Batch

Build one location before ordering all of them. Two acceptance actions settle most open questions. First, install the chosen ONT and enclosure with the cover closed and the expected load connected, then check fit and temperature. Second, simulate a failure: a technician isolates power, replaces the ONT and restores the port using the planned access path. Record the time, tools and any drawing change. Then send the table below with a marked-up floor plan and the ONT datasheet.

RFQ fields for ONT locations and enclosures

Procurement field What to submit
Scenario and location Floor, room or service area, ceiling or wall condition, access direction, and a floor plan with each point marked.
Enclosure purpose Fiber outlet panel, passive termination box or an enclosure that houses an active ONT. State the boundary between active and passive items.
ONT and connectors Model and datasheet, mounting orientation, bracket, connector type, device-plus-plug dimensions, and bend space for fiber and copper.
Power and backup Local adapter or compatible remote DC feed, ONT input requirement, downstream PoE load, services to keep during an outage and the backup target.
Heat and access Ambient temperature in the space, the device's permitted range, loaded sample check, usable opening size, door swing and replacement steps.
Passive materials Part number or specification, empty or pre-loaded, adapter count and end face, splice or pre-terminated method, slack and strain relief, cable entry direction, labels and spares.

Send us your ONT datasheet and outlet layout so we can help match the passive fiber termination hardware to your installation.
Request a Quote

Frequently Asked Questions

Can you install an ONT above a suspended ceiling?

Yes, when the ONT model is approved for that space and a technician can reach it. Check the datasheet for ceiling or plenum ratings and environmental limits, then confirm the access opening and service route.

Can a fiber wall outlet house an ONT?

Check the drawing to see what the outlet is. A fiber termination point holds adapters and fiber, and an ONT position holds powered equipment. A passive outlet such as the GL-2-B is the first kind.

Does an ONT need local power?

An ONT needs power, and the source depends on the model. Some units take a local adapter, and some support a compatible remote DC feed. Confirm which the datasheet lists.

Sources

Vendor specifications are quoted from the listed pages as read in November 2026. Confirm them against current datasheets and drawings before ordering.

Ningbo Glory Optical Communication Co., Ltd. · Passive fiber optic products since 2008 · gloryoptics.com

Send Inquiry