Reinforced Nylon ADSS Dead-End Clamp

Send Inquiry
Reinforced Nylon ADSS Dead-End Clamp
Details
The reinforced nylon dead-end clamp secures 3–6 mm ADSS fiber cable at outdoor termination points. Its ribbed PA66 shell houses a pair of plastic gripping wedges, while a flexible 304 stainless steel bail connects the body to the anchor fitting. The listed assembly measures 340 × 57 × 34 mm, weighs 118 g and has a breaking load of 4.5 kN. Use the cable diameter, required working tension and fitting geometry to review the complete assembly before ordering.
Category
Fiber Tool
Share to
Description

Reinforced Nylon ADSS Dead-End Clamp

The reinforced nylon dead-end clamp secures 3–6 mm ADSS fiber cable at outdoor termination points. Its ribbed PA66 shell houses a pair of plastic gripping wedges, while a flexible 304 stainless steel bail connects the body to the anchor fitting. The listed assembly measures 340 × 57 × 34 mm, weighs 118 g and has a breaking load of 4.5 kN. Use the cable diameter, required working tension and fitting geometry to review the complete assembly before ordering.

Product line: Aerial ADSS Cable Anchoring Hardware

Complete ADSS Dead-End Clamp of the reinforced nylon ADSS dead-end clamp

ADSS Dead-End Clamp

3–6 mm cable OD · 4.5 kN breaking load

Reinforced PA66 · 304 stainless steel bail

Check Specifications   Ordering Details

Shell, Cable Channel and Bail

Review the Clamp at the Termination

Check cable diameter at the grip location

Measure the outside diameter of the jacket where the clamp will sit and compare it with the 3–6 mm range. Use the cable drawing and tolerance when the measurement is near either limit. A route can contain more than one cable construction, so record the diameter against each termination point before issuing a common hardware list.

Review how the two wedges sit

The open tapered shell accepts a pair of plastic wedges. Their toothed faces contact the cable jacket as the wedges seat in the body. At sample review, check how the wedges meet the jacket and whether the installer can reach the opening from the intended working position. Include the cable sample when confirming the fit.

Allow room for the bail and body

The 304 stainless steel bail connects the clamp to the pole or wall fitting. Review the shape and size of the mating attachment with the body in the intended position. Use the assembly dimensions to reserve clearance from nearby hardware. Check the cable approach as well, since it determines how the grip lines up with the span.

Record breaking load and working tension separately

The specification table gives a breaking load of 4.5 kN for the PA66 and 304 stainless steel configuration. Record this value in the breaking-load field of the hardware schedule. Use the route design and approved working-load data to determine the allowable installation and service tension for the combined cable, clamp and support fitting.

Mechanical and Packing Specifications

Parameter Specification
Cable type ADSS fiber optic cable
Cable outside diameter 3–6 mm
Body material Reinforced PA66 nylon, UV-resistant
Grip Two toothed plastic wedges in an open tapered shell
Suspension bail Flexible 304 stainless steel wire
Assembly size 340 × 57 × 34 mm
Unit weight 118 g
Breaking load 4.5 kN
Carton quantity 80 pieces
Outer carton 40 × 30 × 30 cm

Plan the Fixing Point and Delivery

Plan an end pole before the crew arrives

Use the pole drawing to identify the anchor position and the direction from which the cable approaches it. Where the pole carries other fittings, check that there is enough room to place the clamp and engage the bail. Record the cable diameter, fitting drawing and required tension together on the installation schedule.

Review anchors near a building entry

A wall fixing can provide a termination point when its attachment matches the bail and the building layout allows the cable to leave the clamp cleanly. Lay out the straight section at the grip before routing the cable toward the entry. Check the downstream bend against the cable supplier's radius limit and keep the anchor and entry details on the same drawing for the site review.

Prepare replacements for an existing route

Start from the installed cable and the available fixing point. Measure the jacket, photograph the hardware and check whether the body has clearance in the existing position. A sample review can resolve the fit before a replacement lot is allocated to sites that use several cable sizes or attachment types.

Allocate cartons by termination point

The listed pack contains 80 clamps in a 40 × 30 × 30 cm carton. Count the clamp positions on the route drawings, then group the quantities by site and delivery phase. If other clamp sizes ship in the same order, assign a separate carton label to each configuration. Reconcile labels at delivery.

Ordering Details

Check Details to provide
Cable data ADSS construction, nominal outside diameter and jacket tolerance at the grip
Fitting data Drawing or photograph of the attachment and nearby hardware
Load data Required working tension and the breaking-load criterion used by the project
Sample review Cable sample and any clearance or access limits at the termination
Packing instructions Quantity per site, carton labels and delivery allocation

Request a Fit Check

Outdoor Fiber Optic Cables

About Glory Optical

Glory Optical manufacturing facility in Ningbo, China

Glory Optical facility, Ningbo

Glory Optical

Founded in 2008 · Ningbo, China · OEM/ODM support

Glory Optical supplies passive fiber network components from Ningbo, where the company was established in 2008. Its range covers outdoor optical cable, connection assemblies, enclosures, splitters and installation hardware.

Manufacturing & OEM/ODM Support

Tooling, molding and assembly support custom orders across the range. Drawings and approved samples can be used to agree on part construction, product labels and packing before the order is prepared.

Testing Capabilities

The following videos show examples of Glory Optical's inspection and testing activities.

Water Spray Testing

Watch on YouTube

Sealing Performance Testing

Watch on YouTube

Water Resistance Testing

Watch on YouTube

Project Supply & OEM Support

For an aerial route, send the cable datasheet, fitting detail and site quantities together. Glory Optical can use those records to discuss samples and the configuration to list on the order.

About Glory Optical | OEM/ODM Services

Discuss Your Product or Project Requirement

Include the route hardware schedule or the relevant drawing with the quotation request.

Request a Quote | Email Sales

Email: sales@gloryoptic.com

Hot Tags: reinforced nylon adss dead-end clamp, China reinforced nylon adss dead-end clamp manufacturers, suppliers, factory, fiber optic cable tool kit, fiber optic connector tool, fiber optic ftth tool kit, fiber optic termination kit, fiber optic termination tool kit, fiber optic tool kit

Send Inquiry