Tool-Free ADSS Suspension Clamp

Send Inquiry
Tool-Free ADSS Suspension Clamp
Details
The ADSS suspension clamp supports round all dielectric self supporting cable at intermediate points along an aerial route. A split thermoplastic rubber insert surrounds the jacket inside a galvanized steel shell. The wing fastener allows the clamp to close by hand. Four insert sizes cover cable outside diameters from 5 to 20 mm, so the cable size and pole attachment can be specified separately.
Category
Fiber Tool
Share to
Description

Tool-Free ADSS Suspension Clamp with TPR Insert

The ADSS suspension clamp supports round all dielectric self supporting cable at intermediate points along an aerial route. A split thermoplastic rubber insert surrounds the jacket inside a galvanized steel shell. The wing fastener allows the clamp to close by hand. Four insert sizes cover cable outside diameters from 5 to 20 mm, so the cable size and pole attachment can be specified separately.

Product line · ADSS Aerial Suspension Hardware

ADSS Suspension Clamp of the ADSS suspension clamp

Hand Closure with a Split TPR Insert

Four insert sizes for 5–20 mm round ADSS cable

Galvanized steel shell · 3.8 kN breaking load

Compare Cable Sizes   Ordering Details

How the Clamp Supports the Cable

The split insert fits around the cable

The opening runs from the edge of the TPR insert to the round seat. At an intermediate support, this design lets the insert fit around a continuous cable without threading its end through the clamp. In a sample review, check that the jacket lies in the round seat and that the insert sits evenly against the surrounding shell.

The wing fastener closes the clamp by hand

The photos show the wing fastener beside the split insert. Allow enough room to reach it after the pole attachment is in place. Tool free closure refers to the clamp body. A hook bolt, pole band or bolted connection has its own mounting requirements, and the crew should use the hardware specified for that support.

Select the insert using cable outside diameter

Start with the diameter and tolerance on the ADSS cable drawing, then check the supplied jacket against them. The four catalog ranges meet at 8, 12 and 15 mm. If a cable sits near one of these boundaries, review the actual diameter range and trial the proposed insert with a cable sample before assigning it to the route.

Use the load figure for the correct check

The catalog lists a 3.8 kN breaking load for each diameter band. The permitted service load depends on the approved suspension assembly and the conditions at the support. Keep the breaking load in a separate field from the design load for the position. Submit the required load with the support detail when requesting a selection review.

Diameter, Weight and Packing Reference

Parameter Specification
Cable Round ADSS optical cable
Shell and insert Galvanized steel shell with split TPR insert
Catalog size 130 × 70 × 35 mm
5–8 mm cable OD 156 g per clamp
8–12 mm cable OD 155 g per clamp
12–15 mm cable OD 152 g per clamp
15–20 mm cable OD 148 g per clamp
Breaking load 3.8 kN for all four catalog sizes
Packing 4 pieces per subpack, 100 pieces per carton
Outer carton 40 × 30 × 20 cm

Choose the Pole Attachment

Split Insert and Wing Fastener of the ADSS suspension clamp

Split Insert and Wing Fastener

The detail shows the split from the edge of the insert to the round cable seat, with the wing fastener beside it.

Hook bolt suspension

For a pole with a hook bolt, review the shape and opening of the mating connection on the pole drawing. Allow room for the clamp to hang in the intended position and for the cable to leave on both sides. A support sketch should show the direction of the incoming and outgoing spans. An optional stainless steel hook can be specified when required by the support detail. Include the requested hook material and the mating fitting on the drawing so procurement can distinguish the hook option from the standard galvanized steel shell and its associated mounting hardware.

Band mounted or bolted supports

The mounting plate shown in the catalog can be paired with banding or a bolted connection. Use the pole detail to establish where the clamp sits relative to adjacent fittings. The catalog size in the table is a selection reference. Use the selected assembly drawing to check the projection of the wing fastener and the available space for access.

Check the cable path at the support

Review the route where the cable enters and leaves the insert. Use the cable manufacturer's bend requirements and the project's suspension criteria to assess the transition. Where consecutive spans differ in direction, record the line geometry for review so the approved hardware matches the conditions at that pole.

Allocate inserts by cable schedule

Mark the outside diameter band on each work pack and match it to the poles listed for that cable. The packaging reference groups four clamps per subpack. Keep subpacks identified when sharing a carton among crews, especially when nearby sections of the route use cable sizes on either side of the same diameter boundary.

Ordering Details

Check Details to provide
Cable data Outside diameter, jacket tolerance and cable drawing
Pole connection Hook bolt, banding or bolted detail with available clearance
Support requirements Route geometry and required load at each suspension point
Quantities Clamp counts by diameter band and delivery location

Request a Clamp Selection Review

Outdoor Fiber Optic Cables

About Glory Optical

Glory Optical manufacturing facility in Ningbo, China

Glory Optical facility, Ningbo

Glory Optical

Founded in 2008 · Ningbo, China · OEM/ODM support

Glory Optical was established in Ningbo in 2008. We supply passive fiber network products, including optical cable, connectivity assemblies, splice closures, fiber boxes, splitters and installation hardware.

Manufacturing & OEM/ODM Support

Our production capabilities include tooling development, enclosure molding and component and cable assembly. For project supply, we use the approved samples and drawings to agree on the construction and packing.

Testing Capabilities

The videos show examples of testing carried out at Glory Optical.

Water Spray Testing

Watch on YouTube

Sealing Performance Testing

Watch on YouTube

Water Resistance Testing

Watch on YouTube

Project Supply & OEM Support

For an ADSS enquiry, share the cable schedule and the pole connection details. We can review the diameter bands and the sample information required to prepare the order.

About Glory Optical | OEM/ODM Services

Discuss Your Product or Project Requirement

Include the quantities for each cable diameter band with your enquiry.

Request a Quote | Email Sales

Email: sales@gloryoptic.com

Hot Tags: tool-free adss suspension clamp, China tool-free adss suspension clamp manufacturers, suppliers, factory, fiber optic connector tool kits, fiber optic termination kit, fiber optic tool bag, fiber optic tool kit, fiber tool, ftth tool kit

Send Inquiry