ADSS Wedge Anchor Clamp

Send Inquiry
ADSS Wedge Anchor Clamp
Details
This wedge anchor clamp secures round ADSS cable at outdoor dead-end and strain points. Two toothed plastic wedges sit inside an open, tapered PA6 body, and a flexible stainless steel bail connects the assembly to the anchor fitting. The illustrated configuration uses a 201 stainless steel bail and covers cable outside diameters of 3–9 mm. Its published tensile specification is 3 kN.
Category
Fiber Tool
Share to
Description

ADSS Wedge Anchor Clamp with Stainless Steel Bail

This wedge anchor clamp secures round ADSS cable at outdoor dead-end and strain points. Two toothed plastic wedges sit inside an open, tapered PA6 body, and a flexible stainless steel bail connects the assembly to the anchor fitting. The illustrated configuration uses a 201 stainless steel bail and covers cable outside diameters of 3–9 mm. Its published tensile specification is 3 kN.

Product line: ADSS Cable Anchoring Hardware

Assembly Overview of the ADSS wedge anchor clamp

3 kN ADSS Anchor Clamp

3–9 mm cable OD · Reinforced PA6 body

201 stainless steel wire bail

View Dimensions   Check Fit

Cable Channel, Bail and Outline

How the Clamp Fits the Anchor

Side access to the cable channel

The open housing gives the crew access to the wedge channel from the side while positioning the cable at the anchor.

Paired wedges in a tapered body

The plastic jaws seat inside the taper. Their toothed faces contact the cable jacket as the wedges close around the cable.

Reinforced polymer housing

The ribbed, glass-fiber-reinforced nylon body uses UV-resistant material for outdoor installation.

Flexible bail connection

The wire bail connects the clamp to a compatible pole fitting. Check the fitting profile and available clearance against the outline drawing.

Carton planning

The listed pack contains 50 clamps. The outer carton measures 40 × 30 × 26 cm.

Dimensions and Mechanical Data

Parameter Specification
Cable type ADSS optical cable
Cable outside diameter 3–9 mm
Published tensile specification 3 kN
Body Glass-fiber-reinforced PA6 nylon
Grip Pair of toothed plastic wedges
Bail on illustrated configuration 201 stainless steel wire rope
Overall length, drawing reference 420 ± 5 mm
Body width × depth, drawing reference (63 ± 2) × (35 ± 2) mm
Carton quantity 50 pieces
Outer carton 40 × 30 × 26 cm

Where to Use the Clamp

Terminate an aerial ADSS run

At the end pole, coordinate the cable route, wedge position and anchor fitting so the cable enters the clamp along its intended axis. Check the jacket's outside diameter at the grip location before allocating the clamp to that pole.

Plan a strain point at a route change

Where an aerial route uses a strain assembly, check the span tensions and the space needed for each bail and cable lead. Use the route design to determine the allowable working tension and the hardware required at the pole.

Check a replacement against installed hardware

Measure the existing cable jacket and compare the available clearance with the outline drawing. Send a photo or sketch of the installed anchor fitting when requesting a replacement, especially if the project calls for a particular stainless steel grade.

Match the Clamp to the Pole Fitting

Check Details to provide
Cable Jacket outside diameter and cable datasheet
Pole attachment Fitting drawing or photo, with available clearance
Mechanical requirement Design tension at the anchor and required hardware rating
Bail grade and quantity Required stainless steel grade and quantity per site

Request a Fit Check

Outdoor Fiber Optic Cable

About Glory Optical

Glory Optical manufacturing facility in Ningbo, China

Glory Optical facility, Ningbo

Glory Optical

Founded in 2008 · Ningbo, China · OEM/ODM support

Based in Ningbo since 2008, Glory Optical supplies passive components for fiber networks. Its range covers cable assemblies, distribution boxes, splice closures, splitters and the hardware used to install them.

Manufacturing & OEM/ODM Support

The Ningbo team supports tooling, molding and assembly across the product range. For custom orders, it can work from drawings and samples to align the supplied components, labels and cartons with the project schedule.

Testing Capabilities

The videos show examples of Glory Optical's inspection and test work across its product range.

Water Spray Testing

Watch on YouTube

Sealing Performance Testing

Watch on YouTube

Water Resistance Testing

Watch on YouTube

Project Supply & OEM Support

For aerial hardware orders, share the cable datasheet and a drawing of the pole fitting. The team can review the clamp configuration, sample needs and quantities for the planned route.

About Glory Optical | OEM/ODM Services

Discuss Your Product or Project Requirement

Send the cable diameter, anchor fitting and required quantities for a quotation. Include any bail material or carton labeling requirements.

Request a Quote | Email Sales

Email: sales@gloryoptic.com

Hot Tags: adss wedge anchor clamp, China adss wedge anchor clamp manufacturers, suppliers, factory, fiber optic cable termination kit, fiber optic cable tool kit, fiber optic connector tool, fiber optic termination tool kit, fiber tool, fiber tool box

Send Inquiry