Round FTTH Drop Cable Tension Clamp

Send Inquiry
Round FTTH Drop Cable Tension Clamp
Details
This round FTTH drop cable tension clamp anchors an aerial service drop at a dead end. The molded nylon body guides the cable around a circular path, and a buckle closes over the routed cable. The listed range for round cable is 2–6 mm outside diameter. Choose the clamp with the actual drop cable in hand so the winding path, closure and exit can be checked together.
Category
Fiber Tool
Share to
Description

Round FTTH Drop Cable Tension Clamp

This round FTTH drop cable tension clamp anchors an aerial service drop at a dead end. The molded nylon body guides the cable around a circular path, and a buckle closes over the routed cable. The listed range for round cable is 2–6 mm outside diameter. Choose the clamp with the actual drop cable in hand so the winding path, closure and exit can be checked together.

Product line · FTTH Aerial Drop Cable Clamps

Round FTTH Drop Cable Tension Clamp of the round FTTH drop cable tension clamp

Circular Winding Body and Buckle

2–6 mm round cable OD

UV resistant nylon · Custom colors

Check Cable Fit   Ordering Details

How the Cable Sits in the Clamp

The winding path distributes contact around the body

The cable follows the circular guide through the clamp. This layout brings a longer section of jacket into contact with the body. During a sample trial, follow the supplied winding instructions and watch how the jacket sits as it enters and leaves the guide. A cable that rides over the edge or crosses the path needs a fit review before the configuration is approved.

The buckle gives the crew a visible closure check

Check the buckle with the selected cable already seated in the guide. The closure should reach its intended position with the cable clear of the latch faces. The approved sample can then serve as a reference for what the closed buckle looks like. Put that view in the job sheet alongside the open view so the crew can inspect the assembly consistently.

Choose the exit direction before securing the drop

The clamp uses an angled outlet to guide the cable away from the winding body. Plan the exit toward the next routing point, especially where the drop turns near a wall or building entry. The outlet sets a direction, while the cable datasheet sets the minimum bend radius. Leave enough space for the outgoing cable to make the transition without bearing on an adjacent edge.

Specify nylon and color as separate selections

UV resistant PA6 or PA66 nylon options are listed for this design. Identify the selected resin in the purchase description and provide a physical swatch or a color reference when ordering a custom shade. Review the material and color on the same approved sample. That sample provides a consistent reference if subsequent deliveries need to match clamps already staged for the project.

Cable Fit and Construction

Parameter Specification
Primary use Dead end anchoring of aerial FTTH service drops
Round cable outside diameter 2–6 mm
Body Injection molded nylon with UV protection
Nylon options PA6 or PA66, depending on configuration
Cable routing Circular winding guide with angled outlet
Closure Buckle
Color Custom options by approved sample

Prepare the Clamp for the Route

Color Samples for Project Orders of the round FTTH drop cable tension clamp

Color Samples for Project Orders

The sample photo shows three colors for visual reference. Approve the actual color and nylon selection together before production.

Screen the cable profile at the workbench

Use a sample of the cable that will be installed, including its production jacket and any molded features along the grip section. Check the outside diameter at more than one point along a round cable. If the jacket has raised ribs or seams, include those features when comparing the sample with the guide opening. If a project uses a flat profile as well, provide its width and thickness separately and trial it in its own configuration.

Review the first drop at the point of installation

At the first termination, check access to the buckle and follow the intended direction from the clamp to the next guide. Note how the suspension loop meets the existing attachment and whether the installer can see the closed latch from the working position. Record the accepted arrangement with the cable identification for later installations on the same route.

Use project checks for mechanical and optical acceptance

Specify the required service load and acceptance criteria for the selected cable and clamp combination. A trial can include inspection for jacket movement or marking and an optical check under the conditions defined for the project. Record which cable and clamp were evaluated so results remain traceable when the cable jacket, resin or routing arrangement changes.

Stage kits by cable profile and installation zone

Keep round and flat cable hardware on separately labeled lines in the site schedule. If the project uses color to identify a zone or deployment phase, include the same color reference on the packing list and kit label. Keep the physical cable identification visible on each kit so the crew can match the clamp to the intended cable at issue.

Ordering Details

Check Details to provide
Cable sample Round cable outside diameter, jacket details and the cable datasheet
Route detail Suspension attachment, exit direction and the available bend space
Acceptance criteria Service load and the mechanical and optical checks required by the project
Supply details Nylon selection, color sample and quantities by site

Request a Fit Check

FTTH Drop Cables

About Glory Optical

Glory Optical manufacturing facility in Ningbo, China

Glory Optical facility, Ningbo

Glory Optical

Founded in 2008 · Ningbo, China · OEM/ODM support

Glory Optical has operated from Ningbo, China, since 2008. We supply passive components for fiber networks, including optical cable, connection assemblies, distribution boxes, closures, splitters and installation hardware.

Manufacturing & OEM/ODM Support

Our manufacturing work spans tooling development, enclosure molding and cable and component assembly. For custom supply, drawings and approved samples give both teams a reference for production and inspection.

Testing Capabilities

These videos show testing activities carried out at Glory Optical.

Water Spray Testing

Watch on YouTube

Sealing Performance Testing

Watch on YouTube

Water Resistance Testing

Watch on YouTube

Project Supply & OEM Support

Send the cable sample information, the intended route and any finish requirements when asking about a clamp. Our team can use them to prepare a sample request and discuss how the parts will be identified at delivery.

About Glory Optical | OEM/ODM Services

Discuss Your Product or Project Requirement

Include the cable type and quantity in the quotation request.

Request a Quote | Email Sales

Email: sales@gloryoptic.com

Hot Tags: round ftth drop cable tension clamp, China round ftth drop cable tension clamp manufacturers, suppliers, factory, fiber cable termination kit, fiber optic cable termination kit, fiber optic termination kit, fiber optic termination tool kit, ftth tool kit, tool kit fiber optic

Send Inquiry